매그스위치, 자석제품, 조선용 치공구, 면취기, 푸셔, 매그드릴, 중량물 리프팅 솔루션
NPC-A
| WLL(TON) | Jaw Opening | A | B | C | D1 | D2 | E | F | ØG | I | ØJ | K | Weight(kg) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | 0-25 | 30 | 30 | 168 | 25 | 25 | 46 | 98 | 38 | 17 | 25 | 40 | 2.7 |
| 1.5 | 0-25 | 25 | 32 | 166 | 25 | 25 | 46 | 98 | 38 | 18 | 28 | 45 | 2.7 |
| 2 | 0-30 | 30 | 35 | 182 | 25 | 25 | 46 | 100 | 40 | 20 | 30 | 50 | 2.9 |
| 0-40 | 45 | 30 | 182 | 25 | 25 | 46 | 103 | 40 | 20 | 30 | 48 | 3.1 | |
| 3 | 0-35 | 40 | 38 | 205 | 30 | 38 | 46 | 116 | 42 | 22 | 36 | 60 | 4.4 |
| 0-60 | 65 | 40 | 235 | 30 | 40 | 51 | 121 | 45 | 22 | 36 | 61 | 6.3 | |
| 0-100 | 105 | 50 | 323 | 37 | 55 | 60 | 162 | 50 | 30 | 36 | 75 | 16.1 | |
| 5 | 0-50 | 52 | 52 | 265 | 35 | 50 | 59 | 152 | 55 | 28 | 40 | 70 | 10.3 |
| 0-70 | 75 | 55 | 295 | 38 | 50 | 62 | 160 | 55 | 30 | 40 | 70 | 12.0 |
| No. | ASS’Y NAME | No. | PART NAME | No. | ASS’Y NAME | No. | PART NAME |
|---|---|---|---|---|---|---|---|
| 1 | BODY | - | - | 4 | BEARING ASS’Y | 4-1 | BEARING |
| 2 | SCREW ASS’Y | 2-1 | SCREW | 4-2 | SPRING PIN | ||
| 2-2 | HANDLE | 5 | END PLATE | - | - | ||
| 3 | SWIVEL JAW | - | - | 6 | SNAP RING | - | - |
Features
- The NPC-A is a screw clamp used to prevent accidents caused by the widening, slipping or breakage of the hook because the load is
concentrated at the end of the hook when hanging the hook of a lever block and a chain block directly on a work piece.
- The NPC-A is a safe clamp designed to prevent a work piece from slipping as the jaw opening of the clamp gets smaller by the slope which
is proportional to the load on the spherical swivel jaw built in the jig bearing which works as gearing on the opposite side of the screw.
How to use
Insert a steel plate into the inside end of the clamp's jaw opening and then completely tighten the screw.
Warnings
- Do not exceed the rated capacity specified on the clamp.
- Use a work piece only which falls within the jaw opening range specified in the instruction manual.
- If the load is placed laterally, not straightly, on the eye hole, use only 1/2 of the rated capacity.
- Never vertically erect a work piece with this model.
- For horizontal lifting, the clamping point must be two or more. When clamping, the clamps must face each other, not look in one direction.
